平板表面薄圆柱绕流摩擦力矢量场全局测量

针对壁面摩擦力矢量场测量问题,基于剪切敏感液晶(SSLC)涂层技术建立了一种测量平板表面摩擦力矢量场的方法。该方法基于多视角测量原理,采用六台同步相机从不同方向同时采集SSLC涂层在摩擦力作用下的颜色变化,与采用单台相机相比能够降低测量噪声,并且具有测量非定常流动的摩擦力场的潜力。应用该方法测量了平板表面薄圆柱绕流的摩擦力矢量场,结果表明:(1)SSLC涂层能够以彩色方式定性显示壁面摩擦力信息;(2)通过对不同方向观测的SSLC涂层颜色进行分析处理,该方法能够高分辨率测量薄圆柱绕流的摩擦力矢量场,详细地捕获了流动特征;(3)同一份SSLC涂层可以重复使用并且可用于测量不同的摩擦力矢量场。     

基于伴随方法的单级低速压气机气动设计优化

采用梯度方法对某型4.5级压气机最后级进行气动设计优化研究，梯度由连续伴随方法计算确定，多排伴随方程采用伴随掺混面模型进行数值求解。首先，采用基于经验修正的初步设计方法设计带进口导叶的4.5级低速、低压缩比压气机的原始气动外形。之后，在压气机近失速工况对最后级静子叶片进行伴随气动设计优化，通过优化叶型和安装角降低流动损失，目标函数定义为加权求和形式的熵增和流量偏差，优化中对流量进行约束。最后，开展基于伴随方法的多工况气动设计优化研究，改善两个不同转速条件下最后级的气动性能。优化结果表明，基于伴随方法的多排气动设计优化可以通过改变叶片气动外形提升多排全工况气动性能。     

Estimating inter-system biases for tightly combined Galileo/BDS/GPS RTK

The overlapping carrier frequencies L1/E1, L5/E5a and B2/E5b from GPS/Galileo/BDS allow inter-system double-differencing of observations, which shows a clear advantage over differencing of the observations of each constellation independently. However, the inter-system biases destroy the integer nature of the inter-system double-differencing ambiguities. Two methods of direct rounding and parameter estimation are used to determine the ISB value. By analyzing data collected from Curtin University from 2015 to 2018, the phase and code inter-system bias (ISB) are related to the receiver type, firmware version and the selected overlapping frequency. Upgrade of receiver firmware version results in changes of ISB values. For example, the upgrade of Javad firmware in Dec, 15, 2017 causes the difference of 0.5 cycles ISB between BDS GEO and non-GEO satellites. By comparing the three dynamic models which include white noise process, random walk process, and random constant in the parameter estimation method, the ISB determined by the random constant model is consistent with the value obtained by the direct rounding method. After the calibration of ISBs, the performances of tightly combined positioning are assessed. The success rate of ambiguity resolution and accuracy of positioning for the tight combination (TC) are significantly improved in comparison with that for the loose combination (LC) over short baselines. For L5/E5a, on which only few satellites can be observed, the maximum increase in success rates of ambiguity resolution can reach 31.7%, i.e., from 54.9% of LC to larger than 86.6% of TC, and the positioning accuracies can even be increased by 0.13 m, i.e., from 0.208 of LC to 0.074 m of TC in East direction for the mix-receiver TRIMBLE NETR9-SEPT POLARX4 in 2018.     

超高强高韧马氏体时效钢热变形及航天应用研究

对于航天用超高强高韧C300马氏体时效钢来说,热加工过程中获得等轴细小的再结晶晶粒是实现该钢强韧性最佳匹配的关键环节。采用Gleeble-3800热模拟试验机在温度为850～1 150℃、应变速率为0.01～10 s~(-1)的条件下,对超高强高韧C300马氏体时效钢进行高温轴向压缩变形试验,获得了高温流变曲线,并观察变形后的金相组织。结果表明:C300马氏体时效钢的流变应力和峰值应变随着变形温度的升高和应变速率的降低而减小;试验钢在真应变为0.92、应变速率为0.01～10 s~(-1)的条件下,随着变形速率的提高,其发生完全动态再结晶的温度也逐渐升高,最佳热变形温度区间为1 050～1 150℃;测得试验钢的热变形激活能Q值为391.2 kJ/mol,建立了其热变形本构方程。结果能为C300马氏体钢的数值模拟和热加工工艺的制定提供理论基础。     

A novel architecture of electro-hydrostatic actuator with digital distribution

To address the flow imbalance rapidly of the asymmetric Electro-Hydrostatic Actuator (EHA), this paper presents a novel architecture of asymmetric EHA with the Digital Distribution (EHA-DD). It also improves the flow nonlinearity and control accuracy of the pump, especially in the low-speed condition. The digital distribution with two High-Speed on–off Valves (HSVs) not only balances flow instead of the check valves, but also replaces the pump at the low-speed to control output flow by adjusting the PWM signal. The pump and HSVs are the crucial components to control flow output. Firstly, the flow calculation models of the pump and the duty ratio inversed model of the HSV are obtained through experimental tests and the identification method. To get the control input signal for the required flow, the pump speed and PWM duty ratio for the HSVs are inversed to compensate for flow output. Further, a multimode digital flow distribution control method based on pump speed, mainly including the pump-controlled mode for large flow demand and valve-controlled mode for little flow demand, is proposed to control the accurate flow output actively. The step extension experiments based on the flow calculation models are conducted on the EHA-DD prototype under elastic, opposite varying load. The results demonstrate that the EHA-DD realizes little position error by accurate flow control, and it is also beneficial to improve the service life of the pump.     

Evaluation of SARAL/AltiKa performance using GNSS/IMU equipped buoy in Sajafi,Imam Hassan and Kangan Ports

Performance of SARAL/AltiKa mission has been evaluated within 2016 altimeter calibration/validation framework in Persian Gulf through three campaigns conducted in the offshore waters of Sajafi, Imam Hassan and Kangan Ports, while the altimeter overflew the passes 470, 111 and 25 on 13 Feb, 7 March and 17 June 2016, respectively. As the preparation, a lightweight buoy was equipped with a GNSS receiver/choke-ring antenna and a MEMS-based IMU to measure independent datasets in the field operations. To obtain accurate sea surface height (SSH) time series, the offset of the onboard antenna from the equilibrium sea level was predetermined through surveying operations as the buoy was deploying in the onshore waters of Kangan Port. Accordingly, the double-difference carrier phase observations have been processed via the Bernese GPS Software v. 5.0 so as to provide the GNSS-derived time series at the comparison points of the calibration campaigns, once the disturbing effects due to the platform tilt and heave have been eliminated. Owing to comparing of the SSH time series and the associating altimetry 1?Hz GDR-T datasets, the calibration/validation of the SARAL/AltiKa has been performed in the both cases of radiometer and ECMWF wet troposphere corrections so as to identify potential land contamination. An agreement of the present findings in comparison with those attained in other international calibrations sites confirms the promising feasibility of Persian Gulf as a new dedicated site for calibration/validation of ongoing and future altimetry missions.     

A systematic spatial bias in remembering eye positions

Categorical bias in location memory in geometric spaces is well established. The present study assessed the presence of the bias in locating eyes in images of human faces. Participants were presented with digital faces and indicated the position of one of the eyes in both upright and inverted orientations. Biases resulted from participants using multiple sources of accessible information. No differences were found for upright vs. inverted face images. Overall, the data were consistent with the retrieval category adjustment model. These distortions may be considered within the forensic context, when eyewitnesses work with a sketch artist or use a computer program to generate an image of the culprit.     

场协同原理在高超声速化学非平衡流动中的推广

应用理论分析与数值模拟方法，将对流传热的场协同原理从不可压缩流动推广至高超声速化学非平衡流动中。结果表明，高超声速化学非平衡层流与湍流的热流密度取决于流动的当地单位体积的动量与单位质量总焓梯度的协同。用当地单位体积的动量与单位质量总焓梯度的协同研究高超声速化学非平衡流动的壁面传热问题，对层流流动下的对流传热，不但计及了高超声速化学非平衡流的密度变化对热流密度的影响，而且包括了静焓梯度、压力梯度、边界层内的分子黏性剪切效应对热流密度的作用；对湍流问题，除了上述层流流动各项对热流密度的影响外，还计及了雷诺剪切应力对热流密度的作用。考虑到高超声速化学非平衡流静焓的定义，高超声速化学非平衡层流及湍流的场协同同时计及所有组分的平动能、转动能、振动能及电子能等梯度的贡献。     

扩压叶栅叶尖非定常流动的涡动力学机理

为了揭示压气机叶尖区旋涡结构与流动非定常性之间的关联，采用URANS对一亚声速平面扩压叶栅在不同攻角下的流场进行了求解，并借助Q判据提取了叶尖瞬态涡系结构。结果表明：泄漏涡的破碎现象能够通过诱导新的涡结构间接作用于相邻通道的叶尖流动，是导致叶尖流场失稳的关键因素。在-0.3°和+0.7°攻角下，叶尖泄漏涡发生了螺旋破碎，并伴随有非定常诱导涡的出现，诱导涡对相邻叶片载荷的影响使得叶尖泄漏涡发生周期性摆动；在+1.7°攻角下，泄漏涡破碎会导致反流涡的形成，反流涡的输运会给叶片载荷和来流攻角带来非定常扰动，反过来又会作用于泄漏涡的破碎和反流涡的生成，最终表现为一种自维持的非定常流动现象。     

应用后缘装置的跨声速层流翼型多岛优化设计

高雷诺数状态下,自然层流技术(Natural laminar flow,NLF)是减小机翼表面湍流摩擦阻力的有效方法。然而由于层流翼面上大范围顺压梯度的存在使得后缘处的恢复压差更大,产生更强的激波。因此在减小摩擦阻力的同时又增加了激波阻力。本文采用后缘装置(Trailing edge device,TED)来控制翼型后缘处的激波强度,基于线性稳定性理论(Linear stability theory,LST)的eN方法对流动进行转捩判断,进而应用多岛并行多目标进化算法(multi-objective evolutionary algorithm,MOEA)以获得大范围层流区域和弱化激波强度为目标对翼型进行优化设计。优化结果表明合作均衡策略耦合进化算法可以快速地捕捉到该多目标问题的Pareto阵面解,阵面上翼型的波阻力和摩擦阻力性能较初始翼型大大改善。同时,采用后缘装置控制激波强度时,无论在设计点还是偏离设计点时,优化后翼型均具有良好的升阻力特性和鲁棒性。